CENELEC published EN 50742:2026, Safety of machinery – Protection against corruption, on 20 November 2026 after ratification by member countries. It is intended for citation in the Commission implementing decision listing roughly 793 harmonised standards under Regulation (EU) 2023/1230, still being translated into 24 EU languages. Machinery manufacturers must meet the Annex III protection-against-corruption requirement from 20 January 2027, with no sell-off period.
EN 50742:2026, the European standard on protection against corruption (cyber-safety of machinery), has been ratified by CENELEC member countries and was confirmed as officially published on 20 November 2026. It is slated for citation in the forthcoming Commission implementing decision listing harmonised standards under Regulation (EU) 2023/1230, a list covering approximately 793 standards that is still being translated into all 24 official EU languages — meaning the presumption of conformity it will carry is not yet legally available.
Regulation (EU) 2023/1230 replaces Directive 2006/42/EC on 20 January 2027, with no sell-off period for machinery placed on the market after that date. Unlike the Directive it replaces, the Regulation treats protection against corruption — the deliberate or accidental manipulation of safety-related functions — as an essential health and safety requirement in its own right, set out in Annex III.
| Before | After | |
|---|---|---|
| Legal instrument | Directive 2006/42/EC | Regulation (EU) 2023/1230, applying from 20 January 2027 |
| Protection against corruption | Not an essential health and safety requirement in its own right | Essential health and safety requirement set out in Annex III |
| Harmonised standards list | List published under the Machinery Directive, repealed with effect from 20 January 2027 | No harmonised standard cited in the Official Journal under Regulation (EU) 2023/1230 as of 12 November 2026 |
| Sell-off period | — |
That created a structural problem the machinery sector has been living with since 2023: a new, legally binding cybersecurity-adjacent requirement with no normative document telling designers what "adequate" protection looks like. Functional safety standards such as the control-systems series address random and systematic failure, not an attacker who modifies parameters, replaces firmware, or spoofs a signal into a safety-related control system. EN 50742 is the first normative framework specifically addressing safety-related manipulation of machines.
The second problem is procedural. As of 12 November 2026, no harmonised standard was cited in the Official Journal of the European Union under Regulation (EU) 2023/1230, while the harmonised standards list published under the Machinery Directive is repealed with effect from 20 January 2027. Manufacturers therefore face a window in which the old presumption of conformity expires and the new one has not yet been formally published.
EN 50742:2026 is a CENELEC standard, developed under project reference 77624, which provides requirements and recommendations to prevent accidental and intentional corruption of machines, including malicious third-party actions resulting in hazardous situations. The scope is deliberately framed around safety outcomes: the concern is manipulation that produces a hazardous situation, not data confidentiality or commercial IT security.
The document reached the FprEN (final draft) stage as FprEN 50742:2026 and was subsequently ratified by CENELEC member countries. CENELEC management confirmed official publication on 20 November 2026. That confirmation is practitioner-channel intelligence corroborated by the CENELEC project record; the Official Journal citation that converts the standard into a harmonised standard has not yet been published.
Three data points define the current state of play. First, the standard exists and is purchasable through national standards bodies. Second, as of 11 November 2026 there was no harmonised standard cited in the Official Journal for the Annex III protection-against-corruption requirement. Third, the Commission's first harmonised standards list under Regulation (EU) 2023/1230 comprises roughly 793 standards and is expected to run to approximately 350 pages when published — with translation into all 24 official EU languages identified as the remaining bottleneck before adoption.
| Data point | Status | Date |
|---|---|---|
| EN 50742:2026 availability | Standard exists and is purchasable through national standards bodies | Published 20 November 2026 |
| Official Journal citation for Annex III protection against corruption | No harmonised standard cited | As of 11 November 2026 |
| First harmonised standards list under Regulation (EU) 2023/1230 | Roughly 793 standards, approximately 350 pages; translation into all 24 official EU languages is the remaining bottleneck | Not yet adopted |
Regulation (EU) 2023/1230 sets out the essential health and safety requirements for the design and construction of machinery and related products placed on the Union market. Protection against corruption sits in Annex III, in the section referenced in current guidance as 1.1.9, and is accompanied by requirements in the control-systems provisions concerning the traceability of interventions — logs recording modifications to safety-related software and hardware.
The legal mechanism matters here. Compliance with a harmonised standard whose reference has been published in the Official Journal confers a presumption of conformity with the corresponding essential health and safety requirement. A European standard that has been ratified and published by CENELEC but not yet cited in the Official Journal carries no presumption of conformity. It is state of the art — which is evidentially useful in a risk assessment and in any market surveillance dispute — but it does not discharge the burden of proof in the same way.
This is the gap compliance teams need to plan around. EN 50742:2026 is available now. The presumption of conformity attached to EN 50742:2026 under the Machinery Regulation arrives only when the implementing decision is adopted and published.
EN 50742 addresses corruption of machines in the safety sense. The available source material does not describe its clause structure, its relationship to the IEC 62443 series, or whether it defines security levels mapped to performance levels or safety integrity levels. Any claim in those areas is not supported by the sources reviewed here.
No adoption date has been announced. The Commission is preparing a separate harmonised standards list under Regulation (EU) 2023/1230, with the first list expected before the end of 2026; as of mid-November 2026 the list was still being finalised, with translation into all 24 official EU languages explicitly cited as the outstanding work.
The scale explains the delay. A single implementing decision citing approximately 793 standards, running to an estimated 350 pages, must be legally reviewed and produced in 24 language versions simultaneously before publication in the Official Journal. Translation volume of that order is not compressible by prioritising individual standards.
| Parameter | Figure |
|---|---|
| Standards cited | Approximately 793 |
| Estimated length | Approximately 350 pages |
| Language versions required | 24 official EU languages |
| Expected first list | Before the end of 2026 |
| Confirmed adoption date |
The practical consequence: there is a credible scenario in which Regulation (EU) 2023/1230 becomes applicable on 20 January 2027 with the harmonised standards list either published very shortly before that date or shortly after it. Treat any assumption of an orderly hand-over from the Directive list to the Regulation list as an inference, not a confirmed plan.
Secondary guidance circulating in the sector references a Decision 2026/2015 requiring manufacturers to update CE certification or risk losing presumption of conformity. That reference has not been verified against the Official Journal in the sources reviewed and should be checked directly before being relied on.
Every manufacturer placing machinery, related products, safety components or partly completed machinery on the EU market from 20 January 2027 is affected by the Annex III protection-against-corruption requirement. There is no connectivity threshold stated in the sources that would exempt standalone machines — the requirement attaches to the machine, and the risk assessment determines what is reasonable.
The exposure is concentrated in three populations. Builders of networked industrial machinery and lines with remote access, OEM diagnostics or cloud connectivity face the most substantive design work. Builders of autonomous mobile machinery and connected equipment — a category the Regulation expressly brings into focus — face both corruption protection and the broader new requirements. Suppliers of safety components with programmable or machine-learning-based protective functions face the additional consequence that machine learning in protective functions brings notified body involvement into scope under the Regulation.
| Population | Exposure |
|---|---|
| Builders of networked industrial machinery and lines with remote access, OEM diagnostics or cloud connectivity | Face the most substantive design work |
| Builders of autonomous mobile machinery and connected equipment | A category the Regulation expressly brings into focus; face both corruption protection and the broader new requirements |
| Suppliers of safety components with programmable or machine-learning-based protective functions | Machine learning in protective functions brings notified body involvement into scope under the Regulation |
The secondary effect is on notified bodies and test houses. If a substantial share of the installed machinery base requires reassessment against new EHSRs within a period that effectively begins when the harmonised standards list is published, assessment capacity becomes the binding constraint rather than engineering effort. The sources do not quantify notified body capacity; treat the capacity argument as inference from the timeline, not as a published finding.
The obligation is to design and construct the machine so that accidental and intentional corruption cannot create a hazardous situation, and to record interventions in safety-related software and hardware so they can be traced. EN 50742:2026 is the document the Commission and CENELEC intend to be the route to demonstrating this.
In practice this means the risk assessment file must now contain a corruption-related threat analysis for safety functions, not only a hazard analysis. It means the technical documentation must evidence the protective measures chosen and why they are proportionate to the identified hazards. And it means the declaration of conformity issued from 20 January 2027 must reference Regulation (EU) 2023/1230, not Directive 2006/42/EC.
Where EN 50742:2026 is applied before its Official Journal citation, document it as application of a published European standard representing the state of the art, and record the date of publication (20 November 2026) and the version used. If the cited version in the eventual implementing decision differs, that record is what demonstrates the design basis was current at the time of assessment.
Regulation (EU) 2023/1230 applies from 20 January 2027. There is no sell-off period: machinery placed on the market on or after that date must comply with the Regulation. The Machinery Directive harmonised standards list is repealed with effect from the same date.
EN 50742:2026 was published by CENELEC on 20 November 2026 and is available for use immediately, without presumption of conformity. The Commission implementing decision citing approximately 793 harmonised standards under the Regulation, expected to include EN 50742, has no confirmed adoption date; the stated expectation was publication of a first list before the end of 2026, with translation work ongoing as of mid-November 2026.
No enforcement data for the Regulation exists yet, because the Regulation is not yet applicable. Any statement about how aggressively national market surveillance authorities will pursue Annex III corruption-protection non-compliance in 2027 is speculation and is not supported by the sources.
The sources reviewed do not address how the United Kingdom, Switzerland, Turkey or EEA states will treat EN 50742:2026 or the Machinery Regulation harmonised standards list. CENELEC national members outside the EU are obliged to adopt ratified EN standards as national standards under CENELEC internal rules, but that adoption is separate from any presumption of conformity under EU law, and no source here confirms a national adoption date.
Buy EN 50742:2026 through your national standards body this quarter and assign a named owner in functional safety engineering, not in IT security. The standard addresses hazardous situations arising from manipulation; the people who own the performance-level calculations need to own this too.
Run a gap analysis against the Annex III protection-against-corruption requirement for every machine family you intend to place on the EU market on or after 20 January 2027. Prioritise products with remote access, field-updatable safety-related firmware, or programmable safety components — these are where the design changes will be structural rather than documentary. Confirm separately whether any protective function uses machine learning, because that routes the product to a notified body procedure.
Build the intervention logging requirement into the controls architecture now rather than retrofitting it. Logging of modifications to safety-related software and hardware is an architectural decision in most control platforms, not a configuration setting, and it is the requirement most likely to be missed in a documentation-led compliance review.
Do not wait for the Official Journal citation before starting design work. The implementing decision determines when you get presumption of conformity; it does not determine when the obligation applies. The obligation applies on 20 January 2027 regardless.
Finally, set up a monitoring trigger on the Official Journal L-series for implementing decisions under Regulation (EU) 2023/1230. When the 793-standard list is published, check the exact dated version of EN 50742 cited and whether any restriction or note is attached to the citation — restrictions in the third column of a harmonised standards list routinely limit the scope of the presumption of conformity.
The next concrete milestone is adoption and publication in the Official Journal of the Commission implementing decision citing harmonised standards under Regulation (EU) 2023/1230, expected to list approximately 793 standards across roughly 350 pages, with EN 50742:2026 among them. The stated expectation was a first list before the end of 2026; translation into 24 languages was the outstanding task as of mid-November 2026. The hard date remains 20 January 2027, when Regulation (EU) 2023/1230 applies and the Machinery Directive harmonised standards list is repealed.
Watch for the 793-standard implementing decision. The next concrete milestone is adoption and publication in the Official Journal of the Commission implementing decision citing harmonised standards under Regulation (EU) 2023/1230, expected to list approximately 793 standards across roughly 350 pages, with EN 50742:2026 among them.
The publication date of 20 November 2026 and the figures of 793 standards and approximately 350 pages originate from CENELEC and Commission-side communication reported through practitioner channels and are not yet reflected in an Official Journal publication.
Discuss this signal with compliance peers, get the weekly digest, and never miss an enforcement deadline that affects your products.
| No sell-off period for machinery placed on the market after that date |
| None announced |